Revolabs HD Single & Dual Channel User and User Manual

Revolabs HD™ Single/Dual Wireless Microphone System Models: 02-HDSGL, 02-HDDUAL, 04-HDSGLEU, 04-HDDUALEU, 04-HDSGLCN, 04-HDDUALCN

- 10 - To Install the Base Station: 1. Plug the power cord into an appropriate outlet 2. Connect the necessary outputs and inputs Revolabs HD™ Bas

- 11 - 1 2 3 4 5 6 7 8 on off Using the Rear Panel Configuration DIP Switches DIP Switch Feature Off (Default) On 1 Output Mixing Individua

- 12 - DIP Switch 5&6 – Microphone EQ: There are four EQ options for the microphone outputs of the Base Station. One of these options can be activ

- 13 - Mics Unmute at Startup: By default the mics go into a muted state when they are removed from the charger. This is done to prevent handling nois

- 14 - Note: The microphone firmware version must match the Base firmware version for the system to function properly. A mismatch may result in no au

- 15 - 1. Earpiece jack — accepts the 2.5mm plug for the earpiece. 2. Charging port — docks to Revolabs HD Charger Bases. 3. Pocket clip — also use

- 16 - Adjusting the Volume on the Wearable Microphone Earpiece To change the volume on the Wearable microphone earpiece, use the dial on the earpiece

- 17 - 3. With the microphone in position on the table, un-mute the microphone by pressing and releasing the Mute button (confirm by a flashi

- 18 - 5 4 3 2 1 2. Directional Tabletop microphones should be located on the table with the acoustic cover pointed toward the users, trying to keep

- 19 - 1. Audio Out port — accepts the 2.5mm plug for the earpiece. 2. Charging Port — docks to all Revolabs HD Charger Bases. 3. Mute button — pre

© 2010-2014 REVOLABS, INC. All rights reserved. No part of this document may be reproduced in any form or by any means without express written permi

- 20 - 5 4 3 2 1 1. Audio Out port — accepts the 2.5mm plug for the earpiece. 2. Charging Port — docks to all Revolabs HD Charger B

- 21 - 1 2 3 Note: Microphones in new systems must be paired to the Base Station with each microphone assigned to a unique channel on the Base Stati

- 22 - Power Module The Charger Base requires 5VDC power, provided by the AC Adapter. Plug the supplied AC adapter into an appropriate power outlet 11

- 23 - Updating the HD Single/Dual Base Station and HD Microphones 1. Connect to the Base Station using the mini-USB cable. 2. Pair both mics to th

- 24 - Revolabs HD™ Indicator LEDs The following tables show activities associated with the various states shown by the LEDs: Equipment Use Microphon

- 25 - Warranty Revolabs, Inc. warrants this product to be free of manufacturing defects. Repair or replacement of any defective part or unit (at the

- 26 - Specifications Dimensions, (L, W, H) and Weight: Single/Dual Base Station 5.19” (13.18 cm) x 3.25” (8.25 cm) x 1.0” (2.54 cm), 0.325 lbs (0

- 27 - Index Adjusting the Volume, 14 Base Station, 7 Back Panel, 7 Front Panel, 7 Channel LED indicators, 7 Channels, 8 Charger Bays, 19 Charging the

- 28 - Revolabs HD™ Single & Dual Manual 01-HDSGLMAN-PAP-11 April 2014 (Rev 2.9) Note

Contents Safety and General Information ...

- 4 - Safety and General Information Please read the following information to ensure safe and efficient use of your Revolabs system. FCC User In

- 5 - Industry Canada Notice to Users This Class B digital apparatus complies with Canadian ICES-003. Operation is subject to the following two condit

- 6 - Export Law Assurances This product is controlled under the export regulations of the United States of America and Canada. The Governments of the

- 7 - WEEE Notification: The Waste Electrical and Electronic Equipment (WEEE) directive (2012/19/EU) is intended to promote recycling of electrical a

- 8 - Introduction Congratulations on your purchase of a Revolabs Digital Wireless Microphone System! This system utilizes 1.9 GHz DECT technology, an

- 9 - • Acoustic echo cancellation (AEC) • Feedback elimination • Level control • Equalization • Noise cancellation The system is designed to op